User’s Manual SRP-350/352plusIII Thermal Printer Rev. 1.03 http://www.bixolon.com
Rev. 1.03 - 10 - SRP-350/352plusIII 1-2-3 Serial Interface(RS-232C) 1-2-3-1 Single Interface 1-2-3-2 Dual Interface Power Connector S
Rev. 1.03 - 11 - SRP-350/352plusIII Pin No. Signal Name Direction Function Main Frame GND - Frame Ground 2 TXD Output Data Transmission 3 RXD I
Rev. 1.03 - 12 - SRP-350/352plusIII 1-2-4 Parallel Interface(IEEE1284) Pin No. Source Compatibility Mode Nibble Mode 1 Host nStrobe HostClk 2
Rev. 1.03 - 13 - SRP-350/352plusIII 1-2-5 Wireless LAN Interface 1) Wireless LAN Communication Specifications Item Specifications Frequency 2.412
Rev. 1.03 - 14 - SRP-350/352plusIII 1-3 Drawer Cable Connect the cash drawer connecting cable to the cash drawer connector located in the bac
Rev. 1.03 - 15 - SRP-350/352plusIII 1-4 Setting Dip Switches 1-4-1 Serial Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed
Rev. 1.03 - 16 - SRP-350/352plusIII 1-4-3 Bluetooth Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed Enabled Disabled OFF 1-
Rev. 1.03 - 17 - SRP-350/352plusIII 1-5 Installing & Replacing Paper ※ CAUTIONS Be sure to use paper rolls that meet the specifications. Do n
Rev. 1.03 - 18 - SRP-350/352plusIII 1-5-5 Check the orientation of the roll paper when inserting it into the printer. 1-5-6 Pull out a small am
Rev. 1.03 - 19 - SRP-350/352plusIII 1-6 Recommended Papers - TF50KS-E (Paper Thickness: 65μm): Nippon Paper Industries Co., Ltd. - PD 160R (Pap
Rev. 1.03 - 2 - SRP-350/352plusIII Safety Precautions In using the present appliance, please keep the following safety regulations in order to
Rev. 1.03 - 20 - SRP-350/352plusIII 1-8 Removing Paper Jam 1-8-1 When a paper jam occurs, turn the printer off and then back on, open the cover
Rev. 1.03 - 21 - SRP-350/352plusIII 1-9 Adjusting Paper Near-end Sensor Setting SRP-350/352plusIII Series printer has built-in near-end sensors t
Rev. 1.03 - 22 - SRP-350/352plusIII 1-11 Connecting a Computer Use the cable that comes with the printer to connect the printer to computers. 1-
Rev. 1.03 - 23 - SRP-350/352plusIII 2. Self-Test The self-test checks whether the printer has any problems. If the printer does not function prop
Rev. 1.03 - 24 - SRP-350/352plusIII 3. Hexadecimal Dumping This function allows experienced users to see exactly what data is coming to the print
Rev. 1.03 - 25 - SRP-350/352plusIII 4. Specifications Printing Method Thermal transfer printing Dot Density SRP-350plusIII: 180 dpi (7dots/mm) SR
Rev. 1.03 - 26 - SRP-350/352plusIII 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case cle
Rev. 1.03 - 3 - SRP-350/352plusIII CAUTION Violating following instructions can cause slight wound or damage the appliance. Do not
Rev. 1.03 - 4 - SRP-350/352plusIII Warning - U.S.A i) Class A Digital Device : Wired Device This equipment has been tested and found to comply
Rev. 1.03 - 5 - SRP-350/352plusIII Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer
Rev. 1.03 - 6 - SRP-350/352plusIII Introduction to Product SRP-350/352plusIII series printers have been designed to be connected to various typ
Rev. 1.03 - 7 - SRP-350/352plusIII Table of Contents 1. Installing Printer and Getting Started ...
Rev. 1.03 - 8 - SRP-350/352plusIII 1. Installing Printer and Getting Started 1-1 Unpacking Check the following contents list, and contact your d
Rev. 1.03 - 9 - SRP-350/352plusIII 1-2 Interface Connect the printer to the host computer using the right interface cable that complies with the
Commentaires sur ces manuels